FREE SHIPPING on all US orders over $100!

Same day shipping on orders placed before 3PM Eastern, Monday through Friday

The Burris Fullfield Ballistic E3 reticle is designed to help hunters and shooters compensate for bullet drop and wind drift without relying exclusively on riflescope turret adjustments. In addition to a central aiming point, it uses lower vertical holdover references and cascading windage dots to provide additional aiming options at different distances.

When zeroed at 100 yards, the Ballistic E3 reticle's lower vertical references are intended to correspond approximately to 200, 300, and 400 yards for representative ammunition. Its windage dots are designed around an estimated 10 mph crosswind for an average cartridge. These references provide a starting point, but actual results depend on the rifle, ammunition, environmental conditions, and verified ballistic data.

This guide explains how the Burris Ballistic E3 reticle works, what its markings mean, how to interpret its holdover and windage references, and what to verify before relying on it in the field.

What Is the Burris Fullfield Ballistic E3 Reticle?

The Burris Ballistic E3 is a rear focal plane riflescope reticle that combines a conventional central crosshair with additional references for bullet-drop compensation and wind holds. It is designed for use with traditional, magnum, and varmint loads, with its reference points intended to approximate the trajectory and wind drift of representative cartridges.

Instead of making every correction by adjusting the elevation or windage turrets, a shooter can use the reticle's additional markings as aiming references. This can be useful when a target is at a different distance than the rifle's zero or when wind requires an adjustment to the point of aim.

The Ballistic E3 does not automatically measure distance, determine wind speed, or calculate a correction. The shooter must establish the target distance, assess the conditions, and understand how the reticle's references relate to the rifle and ammunition being used.

Understanding the Ballistic E3 Reticle Design

The Ballistic E3 reticle has three main elements:

  • Central crosshair: Provides the primary aiming point and is used when shooting at the established zero distance or when the central aiming point is appropriate for the shot.
  • Lower vertical holdover references: Provide additional aiming points intended to compensate for bullet drop at longer distances.
  • Cascading windage dots: Provide references to the left and right of the central aiming point for estimating windage holds.

These elements work together to provide more information than a conventional Plex reticle. The central crosshair remains the primary reference, while the additional markings help the shooter make adjustments through the aiming point rather than relying solely on turret changes.

How the Ballistic E3 Holdover Lines Work

A rifle's bullet does not travel in a perfectly straight line relative to the scope's line of sight. After leaving the barrel, the bullet follows a trajectory influenced by gravity, its velocity, its aerodynamic characteristics, and atmospheric conditions. As the distance to the target increases, the bullet's path changes relative to the established zero.

The Ballistic E3 addresses this by placing additional references along the lower vertical crosshair. According to Burris, when the reticle is used with a 100-yard zero, the successive lower vertical references are calibrated for approximately 200, 300, and 400 yards, respectively, for an average cartridge.

The purpose of these references is to give the shooter alternative aiming points when the target is beyond the zero distance. Rather than automatically aiming with the central crosshair at every distance, the shooter can use a suitable lower reference when verified ballistic data indicates that it corresponds to the required holdover.

What the Holdover References Do—and Do Not—Mean

The 200-, 300-, and 400-yard labels describe the reticle's intended reference distances under representative ballistic conditions. They should not be treated as guaranteed impact distances for every cartridge or rifle.

Two cartridges can have different trajectories even when their bullet weights are similar. Muzzle velocity, bullet design, ballistic coefficient, and other factors influence how much a bullet drops over a given distance. A holdover reference that works closely with one load may place shots differently with another.

For that reason, the reticle's markings should be verified against the actual rifle and ammunition. A ballistic calculator can help estimate the expected trajectory, but live-fire confirmation at a safe, appropriate range is necessary to establish where the rifle actually impacts.

How the Ballistic E3 Windage Dots Work

Bullet trajectory is only one consideration when aiming at distance. Wind can push a bullet away from its intended path, creating horizontal displacement between the point of aim and the point of impact.

The Ballistic E3 reticle includes cascading dots on either side of the central aiming area. Burris describes these dots as references intended to help compensate for a 10 mph crosswind for an average cartridge. They give the shooter additional aiming points when a windage hold is appropriate.

The direction of the hold depends on the wind and the expected direction of bullet drift. The shooter must estimate the wind's direction and strength, then determine which reference is appropriate. The dots are not a wind sensor and do not independently calculate the correction needed for a particular shot.

Why Wind Conditions Change the Hold

Wind drift varies with the cartridge, bullet, distance, and wind conditions. A full-value crosswind blowing across the bullet's path has a different effect from a wind blowing more directly toward or away from the shooter. Wind speed can also vary along the bullet's path, making the correct hold more difficult to estimate.

The reticle's windage dots provide a reference framework, but they are not a universal wind-drift chart. Use ballistic information appropriate to the load and conditions, and verify the actual relationship between the aiming references and point of impact before relying on them.

Why a 100-Yard Zero Matters

Burris describes the Ballistic E3's standard holdover references in relation to a 100-yard zero. Zeroing establishes the distance at which the rifle's point of impact aligns with the chosen aiming point. The reticle's intended distance references are based on that starting point.

If the rifle is zeroed at a different distance, the relationship between the central crosshair, the bullet's trajectory, and the additional holdover references changes. You should not assume that the same markings will correspond to the same distances when using a different zero.

Before using the Ballistic E3 references, confirm the zero specified for your intended setup and verify the point of impact at known distances. Follow the scope manufacturer's instructions and use an appropriate range with a safe backstop.

Why Ammunition and Ballistics Matter

The Ballistic E3 is designed to work across a range of traditional, magnum, and varmint loads, but those categories include cartridges with substantially different ballistic characteristics. A reticle cannot provide an exact holdover for every possible combination of bullet, velocity, and environmental conditions using distance labels alone.

For a more accurate understanding of the reticle's references, consider the following information:

  • Cartridge and bullet: Identify the exact cartridge and bullet load being used.
  • Muzzle velocity: Use reliable velocity data appropriate to the ammunition and rifle.
  • Bullet characteristics: Bullet weight and aerodynamic performance affect trajectory and wind drift.
  • Zero distance: Confirm the zero distance on which the intended holdover references are based.
  • Environmental conditions: Temperature, air density, elevation, and wind can affect ballistic performance.
  • Magnification setting: Confirm the correct setting for the reticle's intended calibration in the documentation for the exact scope model.

Burris provides ballistic tools that can help estimate bullet drop and windage holds using ballistic and environmental information. Treat calculated results as a starting point and verify them with the actual rifle and ammunition.

Understanding Magnification and Reticle Calibration

The Ballistic E3 is a rear focal plane reticle. In a rear focal plane scope, the reticle appears to remain approximately the same size as magnification changes, while the target image changes size behind it. As a result, the relationship between the reticle markings and the target changes with magnification.

This matters when using a reticle for trajectory compensation. Do not assume that a holdover reference corresponds to the same ballistic distance at every magnification setting. The correct calibration setting depends on the manufacturer's design and instructions for the specific riflescope.

Before using the Ballistic E3 for holdover, consult the documentation for your exact Fullfield model to confirm the intended magnification setting. Then verify the reticle's performance with the ammunition and zero you plan to use.

Burris Ballistic E3 vs. Plex

The main difference between Ballistic E3 and Plex is the additional ballistic information built into the Ballistic E3 design.

Feature Ballistic E3 Plex
Central aiming point Yes Yes
Lower bullet-drop references Yes No graduated holdover references
Windage dots Yes No graduated wind-hold references
Learning curve Requires understanding and verifying the additional references Simple, conventional aiming approach
Best suited to Shooters who want additional holdover and windage aiming options Shooters who prefer an uncomplicated crosshair

Ballistic E3 may be useful when you want additional aiming references available within the scope's sight picture. Plex may be preferable if you want a simpler reticle and expect to use the central crosshair with another method of making corrections.

Neither reticle is automatically the better choice for every shooter. The right option depends on your intended use, how you prefer to make corrections, and whether you are willing to learn and verify the additional references.

Advantages and Limitations of the Ballistic E3 Reticle

Potential Advantages

  • Additional aiming references: Lower vertical markings provide intended holdover references beyond the zero distance.
  • Windage support: Cascading dots provide additional references for estimating wind holds.
  • Less reliance on turret changes for every correction: The reticle offers alternative aiming points when the appropriate hold has been established.
  • Versatile concept: The design is intended for a range of traditional, magnum, and varmint loads, subject to ballistic verification.

Important Limitations

  • Not a universal ballistic solution: Actual holdover and windage requirements vary by rifle, ammunition, distance, and conditions.
  • Requires verification: The printed or implied distance references must be checked against actual point of impact.
  • Wind remains an estimate: The reticle does not measure wind speed or determine the correct hold automatically.
  • Magnification matters: Rear focal plane reticle references must be used according to the calibration guidance for the specific scope.
  • More markings require familiarity: Shooters who do not intend to use holdover or windage references may prefer a simpler reticle.

Frequently Asked Questions About the Burris Ballistic E3 Reticle

What distances are the Ballistic E3 holdover lines designed for?

With a 100-yard zero, Burris describes the lower vertical references as corresponding to approximately 200, 300, and 400 yards for an average cartridge. Actual point of impact depends on the rifle, ammunition, and conditions, so verify the references with your specific setup.

What are the dots on the sides of the Ballistic E3 reticle for?

The cascading dots provide additional aiming references for windage holds. Burris describes them in relation to a 10 mph crosswind for an average cartridge. They do not measure wind or automatically calculate the correct hold for every shot.

Does the Ballistic E3 reticle work with any cartridge?

The reticle is intended for traditional, magnum, and varmint loads, but its reference points will not match every cartridge or load exactly. Verify the ballistic references using information for your specific ammunition and confirm the results at the range.

Do I have to zero my scope at 100 yards?

Burris's stated 200-, 300-, and 400-yard references are based on a 100-yard zero. If you use a different zero distance, do not assume those same references will correspond to the stated distances. Follow the manufacturer's guidance for the intended setup.

Does the Ballistic E3 automatically compensate for wind?

No. The windage dots provide reference points for a shooter to use when estimating a wind hold. The shooter must still assess wind conditions and determine the appropriate correction.

Does magnification affect the Ballistic E3 holdover references?

Because Ballistic E3 is a rear focal plane reticle, the reticle's apparent size remains approximately constant as magnification changes, while the target image changes size. Check the instructions for the exact scope model to determine the correct magnification setting for using its ballistic references.

Is Ballistic E3 better than a Plex reticle?

That depends on how you prefer to aim. Ballistic E3 offers additional holdover and windage references, while Plex provides a simpler crosshair. The additional markings are most useful when you understand and verify how to use them.

Can I rely on the reticle's distance markings without testing them?

No. The stated distances are intended references, not guarantees for every rifle and load. Confirm your zero and verify the point of impact at known distances using a safe and appropriate range setup.

Final Thoughts

The Burris Fullfield Ballistic E3 reticle combines a central crosshair, lower vertical holdover references, and cascading windage dots to give shooters additional aiming options. Its intended 100-yard zero reference provides a starting framework for estimating bullet drop at 200, 300, and 400 yards, while the dots offer references for wind holds.

The key is understanding that these markings are aids, not automatic ballistic calculations. The rifle, ammunition, magnification setting, zero, and environmental conditions all influence how well the references correspond to actual point of impact. Verify the reticle with your specific equipment and use the manufacturer's ballistic guidance before relying on it in the field.